LifePod 2.0

1) To get started, undo both side compression latches to open your LifePod.

Troubleshooting! If the lid is having issues opening, it is likely pressurized. Open the front key cover to release the pressure.

3) Locate the battery cover on the front wall and remove by pressing on the outer tab.

3) Carefully pull out the 9v battery snap inside the battery compartment, and connect an Alkaline 9V battery to the connector. Be sure to snap the battery in the correct orientation A 9v Alkaline battery is not included.

4) When the battery is snapped in you will hear a short welcome tone and the keypad will light up.

5) Once you hear the tone and see the keypad light up, slide the battery into its compartment being mindful to place the battery ribbon underneath the battery first (Fig C). This will make the battery easier to remove when replacing.

6) Replace the battery cover and you are ready to program your LifePod.

Troubleshooting! If the keypad is flashing the battery is likely bad. Test the normal function by removing the battery and plugging in a micro-USB cable to the micro-USB port. If the unit resumes normal function then the installed battery is bad. We recommend a brand name battery like Duracell or Energizer.

Still having issues? Please contact our support team via email at support@vaulteksafe.com.

TIP: Your code can be a minimum of 4 digits, or as long as 8 digits.

• Two keys can not be pressed simultaneously.
• Programming a new code will overwrite your previous code.

1) First open the unit and tap the lock pad to wake the unit up (Fig K). When the keypad lights up, your LifePod is awake and ready for programming.

2) Press and hold the PROGRAM button for 3 seconds (Fig L) until ALL keys (1-4) turn solid RED.

3) Enter your new code.

4) Press and hold the PROGRAM button a second time for 3 seconds (Fig L) until ALL keys (1-4) turn solid RED.

5) Enter your new code a second time.

6) Press and hold the PROGRAM button a third time for 3 seconds (Fig L). The status LED (Fig M) will flash GREEN and LifePod will beep to confirm the code change is successful.

Your Biometric LifePod 2.0 can store up to 20 unique fingerprints. The 1st and 2nd fingerprints will be recognized as administrative fingerprints and will be used to authorize additional users. Please refer to “Programming Admin Fingerprints” to get started.

Fingerprint TIPS!

1. Be sure your finger is flat against the scanner (parallel to safe) and your cuticle is over the center of the scanner (this allows the scanner to read where most of the fingerprint details are located).
2. Rotate your finger slightly during registration scans.

IMPORTANT: The manual key can not lock LifePod.

IMPORTANT: Before locking your LifePod, always be sure the side compression latches are latched closed first. This will ensure the locking mechanism engages properly.

To lock, simply press and hold the lock pad for 2 seconds.

You have two ways of unlocking LifePod either a master code or the included keys.

IMPORTANT Do not undo the compression latches until the unit has been unlocked with the
correct master code first. Undoing the compression latches first may cause binding on the lock mechanism and will not unlock.

1) First tap the lock pad to wake the unit up. When the keypad lights up, your LifePod is awake and
ready to accept the code.

2) Enter the master code. (The default master code is 1-2-3-4). When the code is correct, the status LED will turn GREEN and the lock will disengage.

3) Undo both side compression latches, and you can open the unit.

TIP: Your LifePod can protect your belongings against the elements using the side compression latches alone. For extra security, lock the unit with the lock pad as needed.

Vaultek strongly encourages you to register your LifePod 2.0 as soon as receive it. Registration provides many benefits including technical support and ordering replacement keys should you replace them. Your LifePod 2.0 has a unique product part number on the inside of the batty door and a 4-digit ID number engraved on the keys. You will need these numbers to register your new unit.

1. Locate your product part number. It is printed on the first page of your user manual and on the back of the battery cover.

2. Find your 4-digit number engraved on the keys.

3. A copy of your receipt or order number.

4. You are ready to register your LifePod 2.0.

IMPORTANT: The manual key can not lock LifePod.

IMPORTANT: Before locking your LifePod, always be sure the side compression latches are latched closed first. This will ensure the locking mechanism engages properly.

To lock, simply press and hold the lock pad for 2 seconds.

You have two ways of unlocking LifePod either a master code or the included keys.

IMPORTANT Do not undo the compression latches until the unit has been unlocked with the
correct master code first. Undoing the compression latches first may cause binding on the lock mechanism and will not unlock.

1) First tap the lock pad to wake the unit up. When the keypad lights up, your LifePod is awake and
ready to accept the code.

2) Enter the master code. (The default master code is 1-2-3-4). When the code is correct, the status LED will turn GREEN and the lock will disengage.

3) Undo both side compression latches, and you can open the unit.

TIP: Your LifePod can protect your belongings against the elements using the side compression latches alone. For extra security, lock the unit with the lock pad as needed.

Backup keys can not lock LifePod.

Backup keys are provided in case of battery failure, allowing you to unlock LifePod. The key hole is located beneath the front protective rubber cover.

To unlock LifePod, simply open the protective cover, insert one of the backup keys, and turn the key clockwise 90 degrees. If the Anti-Picking feature is enabled, the backup keys can not open LifePod.

IMPORTANT: Always make sure the front protective cover is closed tightly to ensure the unit is sealed correctly for protection from the elements.

Your LifePod is equipped with an anti-hacking feature for enhanced security. Using the Anti-Picking feature, you can disable the LifePod from key access. This prevents the front keyway from being picked open, but also prevents the lock from being opened with the manual key.

Important! The manual key can not lock LifePod with either setting.

OFF By default the feature is disabled and allows for normal function of the manual key to unlock LifePod.

ON Front keyway is disabled. LifePod can not be picked open, and the manual keys can not be used to open the unit.

Tip! Remove the tray for larger items. Remove tray for Full Size pistols or (2) Compacts + mags

Tip! Use tray to layer smaller items. Use the tray to layer Sub-Compacts, spare mags, + EDC. (2) velcro straps are provided to secure times to the tray

Status LED
The status LED will provide feedback on various commands. It will light GREEN when correct codes are entered and RED when an incorrect code is entered.

Tamper Indication
If the status LED is solid RED when awake, this means the unit has detected that an incorrect code has been entered. You can clear the tamper indicator by entering the correct master code.

Battery Indicator
When the unit is awake, the battery indicator will light either GREEN or RED. Green indicates the battery has sufficient power, and Red indicates the battery is in need of replacement.

Lock Pad
The lock pad illuminates RED only when the unit has been locked using the keypad, and requires the use of the master code to unlock it. When locked, and the unit is awake, the lock icon will be solid RED.

TIP: If the lock icon is solid RED, do not undo the side compression latches to open the unit. This means the internal lock is engaged and should not be opened. Enter the master code to unlock the unit, as indicated by the lock icon light going OFF. It is now safe to undo the side latches and open the unit.

The interior LED light will come on when the lid is open and stays on for about 20 seconds by default. You have the option to disable the light, or extend the light to stay on longer. To toggle the interior LED light options you need to wake up LifePod by tapping the center Lock Pad then press and hold keys ‘1’ and ‘4’ together. The status LED will indicate the selected light setting per below:

Status LED Solid RED: Interior Light is OFF
Status LED Solid GREEN: Interior Light stays on for 20 seconds.
Status LED Flashing Green: Interior Light stays on for 60 seconds.

By default, the sound is ON. To toggle the sound ON/OFF you need to wake up LifePod by tapping the center Lock Pad then press and hold keys ‘2’ and ‘3’ together. The status LED will flash RED indicating OFF or GREEN indicating ON.

To delete all the stored prints on the LifePod, wake the unit by tapping the lock pad so all the keys light up RED. Immediately, press and hold keys ‘1’ and ‘3’ together for 3 seconds (until the keys turn RED) then enter your master code to delete all fingerprint IDS.

A micro-USB port is built into LifePod behind the front protective rubber cover.

In the event the battery dies while traveling, and you do not have access to the backup keys, you can power on the unit using the backup micro-USB port.

Simply open the rubber cover and plug in a micro-USB cable (not included) into the port. While the cable is plugged into
an external power source, LifePod will function normally allowing you to enter the code and open the unit.

Included is a steel security cable that can be used to secure the LifePod to a fixed object.

1) First wrap the looped end of the cable around an object of your choice, such as a seat bracket under your vehicle’s seat.

2) Pull the adapter piece through the loop, and cinch tight.

3) Place the adapter piece in its slot in the LifePod, and close the lid.

The battery is likely bad. Test the normal function by removing the battery and plugging in a micro-USB cable to the micro-USB port. If the unit resumes normal function then the installed battery is bad. We recommend a brand name battery like Duracell or Energizer.

LifePod’s backup keys are designed to unlock LifePod in the event the battery dies, but they can not lock LifePod. NOTE: Enabling the Anti-picking feature ON, will prevent the keys from being able to unlock LifePod as this feature disables the front keyway altogether.

Test normal function by removing the battery and plugging in a micro-USB cable to the micro-USB port to power the unit so you can unlock and replace the battery. We recommend a brand name battery like Duracell or Energizer.

If the lid is having issues opening, it is likely pressurized. Open the front key cover to release the pressure.

Try the following if you are experiencing a low success rate with the fingerprint scanner.

Let’s perform a soft reset of the scanner by deleting the fingerprints on the safe. Wake the unit by tapping the lock pad so all the keys light up RED. Immediately, press and hold keys ‘1’ and ‘3’ together for 3 seconds until all the keys turn RED then enter your master code to delete all fingerprint IDs. Now let’s try reprogramming your fingerprint using the helpful tips below.

Fingerprint TIPS!

1. Be sure your finger is flat against the scanner (parallel to safe) and your cuticle is over the center of the scanner (this allows the scanner to read where most of the fingerprint details are located).
2. During the 5 scan programming process for each finger, slightly repositioning your finger after each scan will store more information and increase your success rate.
3. Biometric technology is dependent on our anatomical information, and in some cases different fingers may program better than others. For example, your index finger may not register very well, but your thumb may contain higher detail levels and have a much higher success rate. We suggest to try different fingers including your thumb and see if you have better results.
4. To increase success rate register the same finger multiple times. Note, that adding more than two fingerprints requires authorization from the two administrative prints.

Program the First Print

1) Tap the lock pad to wake the unit up.

2) Quickly tap the program button.

3) When the ‘1’ key starts blinking place your fingerprint on the scanner. Place, lift, and rotate until all four keys light up.

4) Test to see if the safe will open using your fingerprint.

Still having issues? Please contact our support team via email at support@vaulteksafe.com.

To order a set of keys, charging kit, or steel cable, fill out our Spare Parts form.

Please email our support team at support@vaulteksafe.com. Be sure to provide your order details and the issue you are experiencing. We look forward to getting this resolved for you!

A new 9v Alkaline battery will last up to one year with normal use. Normal use is locking and unlocking the LifePod 1-2 times per day.

Yes, LifePod qualifies as a secure lockbox for traveling. If transporting firearms, be sure to inform your airline agent when checkin in due to Federal law. Be aware, that you may be asked to open your LifePod, and person having the master code should be present in case such a request is made by a government authority.

Yes, the compression latches are designed to seal the interior chamber from the elements and great for recreational use. The lock can be used when a higher level of security is needed.

LifePod is not fireproof, but is waterproof up to 1 foot deep. It is designed to stay afloat in the water with weight up to 2lb.

The following digital product manuals are available for use.

LifePod 2.0