RS Vehicle Slider

Plug in the safe to a power source using the included power cable. Attach the threaded anti-vibration locking power cable, then use a USB to 12 volt vehicle adapter (not included). This provides continuous power. The power cable does not charge the backup batteries.

Open the safe. The key entry is located at the back of the safe. Remove the battery cover located inside the safe and install four AAA Alkaline batteries. For optimal performance, we recommend Duracell/Energizer or other reputable brands. Rechargeable batteries are not supported and may cause issues. Alkaline batteries only.

Press and hold keys ‘2’ ‘4’ and the Program button together for 3 seconds. The keypad will flash GREEN indicating ON or RED indicating OFF.

If enabled and the ‘1’ key blinks RED several times when opening the safe, the battery level is critically low and the batteries need to be replaced.

Press and hold the ‘5’ key for 3 seconds. Keys ‘1’ to ‘4’ will glow GREEN or RED to indicate the battery level.

Press and hold the ‘1’ and ‘3’ keys together for 3 seconds to adjust the sound setting.

The sound setting can be adjusted to either Low, Medium, High, or OFF.

Press and hold keys ‘3’ ‘5’ and the Program button together for 3 seconds to adjust the interior light setting.

The interior light can be toggled ON/OFF and has different interior light durations either 10 seconds, 30 seconds, or 60 seconds.

Press and hold keys ‘2’ and ‘4’ together for 3 seconds. The ‘3’ key will glow RED to indicate tampering or GREEN to indicate no tampering.

Tampering activates when incorrect keypad entries are entered or incorrect fingerprint scans are made. To reset the tamper detection you must open the safe through one of the authorized entry points.

Press and hold keys ‘3’ ‘4’ and the Program button together for 3 seconds. The keypad will glow GREEN indicating this feature is ON or RED indicating OFF.

If enabled the safe triggers an audible alert if the door remains open for more than 10 minutes.

Press and hold the ‘4’ key and Program button together for 3 seconds. The keypad will glow GREEN indicating this feature is ON or RED indicating OFF.

If enabled the safe requires input of the master code and enrolled fingerprint or vice versa to open the safe. This mode requires that at least one fingerprint be programmed in the safe and the master code is set.

Press and hold keys ‘2’ ‘3’ and the Program button together for 3 seconds. The keypad will flash GREEN indicating ON or RED indicating OFF.

If enabled and someone opens the safe by picking the lock, the keypad will start flashing and an alarm will sound for 10 seconds. To clear the alarm you must enter the master code, scan an authorized fingerprint, or use the backup keys.

Factory Reset erases all programmed information and resets the master code to 2-1-4-2-4-1-3-2. It also restores sound to Medium, the interior light to ON for 10 seconds, Low Battery Warning to ON, Open Door Alarm to ON, Dual Entry Mode to OFF, and Alert of Unauthorized Access to ON.

Open the safe using the included key and leave the key turned all the way in the clockwise position. Press and hold keys ‘1’, ‘5’, and the Program button together until the safe restarts.

• When entering your code, press one key at a time. Two keys cannot be pressed simultaneously.
• We recommend choosing a 6- to 8-digit code for added security.
• Programming a new master code replaces your previous code.
• The default master code is 2-1-4-2-4-1-3-2.

1. Press and hold the ‘1’ key and Program button together for 3 seconds until all keys light up RED and let go.

2. Enter your NEW master code.

3. Immediately press and hold the ‘1’ key and Program button together a second time for 3 seconds until all keys light up RED and let go.

4. Enter your NEW master code a second time.

5. Immediately press and hold the ‘1’ key and Program button a third time for 3 seconds until the keypad flashes GREEN and let go. This indicates the master code has been successfully programmed.

Repeat these steps to change the master code.

• Each fingerprint requires 5 registration scans to be enrolled into the safe.
• Place the core of the fingerprint flat over the center of the scanner.
• Rotate your finger slightly between registration scans to store print variations for increased accuracy.

Program the same fingerprint 4 or 5 times. You have 20 slots available. Try your thumb as it has more surface area for the scanner to read.

1. Press and hold the ‘2’ key and Program button together for 3 seconds.

2. The keypad will turn solid RED and the ‘1’ key will start blinking RED.

3. Scan your fingerprint for the 1st of 5 scans. When the safe beeps and the ‘1’ key lights up GREEN remove your finger.

4. Rotate your finger position and place your finger on the scanner again. You will repeat this process until all keys are solid GREEN.

1. Press and hold the ‘2’ key and Program button together for 3 seconds.

2. The keypad will turn solid RED and the ‘1’ key will start blinking RED.

3. Scan your fingerprint for the 1st of 5 scans. When the safe beeps and the ‘1’ key lights up GREEN remove your finger.

4. Rotate your finger position and place your finger on the scanner again. You will repeat this process until all keys are solid GREEN.

Once both Admin prints 1 and 2 are enrolled you can add additional prints 3 to 20.

1. Press and hold the ‘2’ key and Program button together for 3 seconds.

2. The LED ring around the scanner will turn YELLOW indicating you need to scan one of the admin prints to authorize the additional print. Scan the admin print.

3. Place the new finger on the scanner. When the safe beeps and the keypad lights up GREEN remove your finger. You will repeat this process until all keys are solid GREEN.

Press and hold the ‘3’ key and “Program Button” together for 3 seconds then enter the master code. The keypad will blink GREEN indicating deletion of all the fingerprints.

This will remove all fingerprints enrolled into the safe.

Press and hold keys ‘1’ ‘2’ and the Program button together for 3 seconds. The keypad will flash GREEN indicating enabled or RED indicating disabled.

1. Press and hold the ‘5’ key then the Program button on the safe together (3 seconds) until the keypad flashes RED.

2. Nano Key 3.0: Aim Nano Key towards the safe. Press and hold the button on Nano Key until the indicator LED starts flashing YELLOW.

2. Nano Key 3.0 Biometric: Aim Nano Key towards the safe. Press and hold the button on top of the Nano Key until the scanner LED turns YELLOW. Scan the admin print on the Nano Key scanner. At least one fingerprint needs to be enrolled in Nano Key 3.0 Biometric in order to pair with your Vaultek compatible safe.

3. If the safe beeps and the keypad flashes GREEN then the Nano Key has paired successfully.

Nano Key 3.0 Biometric can store up to 20 unique fingerprints on Nano Key. At least one print needs to be enrolled in order to pair with your compatible Vaultek safe.

Programming Admin Print

1. Press the button located on top of Nano Key 3.0 Biometric.

2. The LED ring will turn solid RED.

3. Scan your finger for the first of three registration scans.

4. Lift and keep scanning the same print until the ring flashes GREEN and you hear a confirmation beep.

Programming Additional Prints

1. Press the button located on top of Nano Key 3.0 Biometric.

2. The LED ring will turn solid YELLOW.

3. Scan an Admin print for authorization.

4. Scan the new finger for the first of three registration scans.

5. Lift and keep scanning the same print until the ring flashes GREEN and you hear a confirmation beep.

Troubleshooting! If the LED ring stays RED, the scan was not accepted. You will need to start again.

Troubleshooting! If the LED ring turns YELLOW after pressing the button on Nano Key 3.0 Biometric then it’s prompting the scan of the Admin print to authorize the new user.

Deleting Fingerprints on Nano Key 3.0 Biometric: Quick tap the button located on top of Nano Key 3.0 Biometric (3 times). The LED ring will glow YELLOW. Scan the Admin print to authorize the deletion of all prints. The LED ring will glow GREEN indicating the deletion is successful.

Press and hold keys ‘1’ ‘4’ and the Program button together for 3 seconds. The keypad will blink GREEN indicating deletion of the paired Nano Key.

Your safe comes with a non-slip mat for the top of the safe, and side guard rails with included hardware that can attach to the safe. Combining the mat and the guard rails allows for non-slip storage on the top of the safe, and guard rails to prevent items from falling off the side and additional securing points.

Once you’ve decided to install the guard rails or not, then it’s time to secure your safe in your vehicle. You can use the two included tether cables to tether your safe in place. Wrap the tether cables around a fixed point in the vehicle and then attach the cables to the safe.

Spacers and three bolt lengths are included to accommodate different cargo floors and truck thresholds. Depending on the placement, the safe’s height can be adjusted to clear a variety of different trunk threshold heights.

Your safe can be bolted down into position. To do this first use the included template, so you can mark and drill your holes ahead of time. Now place the safe into position, remove the foam pad from inside the drawer. Slightly push the safe drawer inward to reveal the pre-drilled holes located at the bottom of the safe. Now secure your safe using the included hardware.

To power your safe in a vehicle first install your batteries, your safe can run on battery power for up to a year under normal use. Second attach the threaded anti-vibration locking power cable, then use a USB to 12 volt vehicle adapter (not included). Your safe now has steady power from the vehicle, and backup power from the installed batteries. The power cable does not charge the installed batteries.

If the safe is left open for more than 10 minutes the Open Door Alarm will sound. To disable the Open Door Alarm, press and hold keys ‘3’ ‘4’ and the Program button together for 3 seconds. The keypad will glow GREEN indicating this feature is ON or RED indicating OFF.

If the ‘1’ key blinks RED several times when opening the safe, the battery level is critically low and the batteries need to be replaced.

Program the same fingerprint 4 or 5 times. You have 20 slots available. Try your thumb as it has more surface area for the scanner to read.

The user manual included with your purchase covers setup instructions, hotkeys, and other essentials to get your safe up and running. Download the RS Vehicle Slider Manual or View All Vaultek Manuals for additional models.

Register your RS Vehicle Slider safe. This provides many benefits including a three year warranty, technical support, and ordering replacement keys should you misplace them.