Vaultek Support

LifePod Series

LifePod Humidor

Support for Humidor

Support for Humidor

Get Started

Easy to follow setup guide.

Get to Know Your LifePod

Discover the full potential.

Manual

Digital product manual.

Warranty

Vaultek satisfaction guarantee.

Register Safe

Improved Support, Product Updates, Replacement Parts.

Get Started

Battery

LifePod humidor is by (2) 9v Alkaline batteries. One powers the Bluetooth Humidor, and and the second powers the LifePod’s built-in locking system.

Install Humidor Battery

1. Undo the side compression latches to open your LifePod. Using the strap, gently lift the interior module out.

2. Locate the battery cover on the reverse side, and remove by pressing on the outer tab.

3. Pull out the 9v battery snap and connect a 9v Alkaline battery.

4. Slide the battery into the compartment and replace the cover.

Install LifePod Battery

1. Locate the battery cover on the from wall of the LifePod and remove it by pressing on the outer tab (Fig A).

2. Carefully pull out the 9v battery snap inside the battery compartment, and connect an Alkaline 9V battery to the connector. Be sure to snap the battery in the correct orientation (Fig B). A 9v Alkaline battery is not included.

3. When the battery is snapped in you will hear a short welcome tone and the keypad will light up.

4. Once you hear the tone and see the keypad light up, slide the battery into its compartment being mindful to place the battery ribbon underneath the battery first (Fig C). This will make the battery easier to remove when replacing.

5. Replace the battery cover and you are ready to program your LifePod.

Program Safe

TIP: Your code can be a minimum of 4 digits, or as long as 8 digits.

  • Two keys can not be pressed simultaneously.
  • Programming a new code will overwrite your previous code.

1) First open the unit and tap the lock pad to wake the unit up (Fig K). When the keypad lights up, your LifePod is awake and ready for programming.

2) Press and hold the PROGRAM button for 3 seconds (Fig L) until ALL keys (1-4) turn solid RED.

3) Enter your new code.

4) Press and hold the PROGRAM button a second time for 3 seconds (Fig L) until ALL keys (1-4) turn solid RED.

5) Enter your new code a second time.

6) Press and hold the PROGRAM button a third time for 3 seconds (Fig L). The status LED (Fig M) will flash GREEN and LifePod will beep to confirm the code change is successful.

Smart Module

The interior Bluetooth module tracks and monitors humidity and temperature. You can track the status of the relative humidity and temperature in the “Vaultek LifePod Humidor” app. Available for Android and iOS devices in your app store. The Bluetooth module also has an audible alarm that can be enabled. If enabled, any threshold that you set from the app will sound an audible alarm on the humidor if thresholds are out of your desired range.

Power Switch

You can switch the Bluetooth module OFF to save power. This disables the Bluetooth and the app function only. This does not affect LifePod’s standard functions such as locking and unlocking.

Audible Alarm

The interior module has an able alarm that can be enabled.

The audible alarm will sound for any of the following reasons and can be adjusted in the settings menu in the app.

Humidity High / Humidity Low
Temperature High / Temperature Low
Low Bluetooth Module Battery (This is not the same battery that’s powering the LifePod)

TIP! If the alarm sounds, disable it from the settings menu in the app. Make any adjustments such as replacing a humidity packet or replace the battery if needed and enable the alarm again.

Bluetooth App

The LifePod Humidor has a Bluetooth enabled interior module that monitors the internal humidity and temperature. Using the Bluetooth companion app from your smarphone, your an view live environmental data when in range of the LifePod (approximately 20-25 feet) and you can manage certain preferences.

Vaultek does not in any way access your personal data (including photos, locations, contacts, etc). The app requires permissions to store certain preferences such as safe settings and fingerprint ID names in the memory of your phone. It also uses the Bluetooth function of your phone for wireless communication with your safe.

Available for Android and iOS devices, search for “Vaultek LifePod Humidor” in your app store.

Setting Environmental Thresholds

Using the app, you can set environmental thresholds for your ideal interior conditions, and if the humidity or temperature values are higher or lower than desired, the app can provide feedback from the main dashboard.

TIP! The app will not send alerts to your phone, but allows you to make convenient maintenance checks when in range. The app dashboard will provide graphical indication of the values and highlight any values out of range.

Seasoning LifePod Humidor

STEP 1

Remove the cedar tray from your LifePod.

STEP 2

Place the cedar tray in an airtight container or zip-lock bag along with an 84% seasoning pack for 3 days.

Boveda makes 60 gram seasoning packs that can be found here: https://store.bovedainc.com/

STEP THREE

Return the battery the Bluetooth module. Then install the cedar tray back inside your LifePod and place a humidity control pack with your preferred %RH inside the control pack pocket on the lid.

Enjoy! https://store.bovedainc.com/collections/boveda-for-tobacco

We recommend reseasoning your Humidor once a year.

Register Your Safe

Vaultek strongly encourages you to register your LifePod Humidor as soon as receive it. Registration provides many benefits including technical support and ordering replacement keys should you replace them. Your LifePod Humidor has a unique product part number on the inside of the batty door and a 4-digit ID number engraved on the keys. You will need these numbers to register your new unit.

1. Locate your product part number. It is printed on the first page of your user manual and on the back of the battery cover.

2. Find your 4-digit number engraved on the keys.

3. A copy of your receipt or order number.

4. You are ready to register your LifePod Humidor.

Get to Know Your LifePod

Locking

IMPORTANT: Before locking your LifePod, always be sure the side compression latches are latched closed first. This will ensure the locking mechanism engages properly.

To lock, simply press and hold the lock pad for 2 seconds.

Unlocking

You have two ways of unlocking LifePod either a master code or the included keys.

IMPORTANT Do not undo the compression latches until the unit has been unlocked with the
correct master code first. Undoing the compression latches first may cause binding on the lock mechanism and will not unlock.

1) First tap the lock pad to wake the unit up. When the keypad lights up, your LifePod is awake and
ready to accept the code.

2) Enter the master code. (The default master code is 1-2-3-4). When the code is correct, the status LED will turn GREEN and the lock will disengage.

3) Undo both side compression latches, and you can open the unit.

TIP: Your LifePodTM can protect your belongings against the elements using the side compression latches alone. For extra security, lock the unit with the lock pad as needed.

Bluetooth App

The LifePod Humidor has a Bluetooth enabled interior module that monitors the internal humidity and temperature. Using the Bluetooth companion app from your smarphone, your an view live environmental data when in range of the LifePod (approximately 20-25 feet) and you can manage certain preferences.

Vaultek does not in any way access your personal data (including photos, locations, contacts, etc). The app requires permissions to store certain preferences such as safe settings and fingerprint ID names in the memory of your phone. It also uses the Bluetooth function of your phone for wireless communication with your safe.

Environmental Thresholds

Using the app, you can set environmental thresholds for your ideal interior conditions, and if the humidity or temperature values are higher or lower than desired, the app can provide feedback from the main dashboard.

TIP! The app will not send alerts to your phone, but allows you to make convenient maintenance checks when in range. The app dashboard will provide graphical indication of the values and highlight any values out of range.

LED Indicators

Status LED
The status LED will provide feedback on various commands. It will light GREEN when correct codes are entered and RED when an incorrect code is entered.

Tamper Indication
If the status LED is solid RED when awake, this means the unit has detected that an incorrect code has been entered. You can clear the tamper indicator by entering the correct master code.

Battery Indicator
When the unit is awake, the battery indicator will light either GREEN or RED. Green indicates the battery has sufficient power, and Red indicates the battery is in need of replacement.

Lock Pad
The lock pad illuminates RED only when the unit has been locked using the keypad, and requires the use of the master code to unlock it. When locked, and the unit is awake, the lock icon will be solid RED.

TIP: If the lock icon is solid RED, do not undo the side compression latches to open the unit. This means the internal lock is engaged and should not be opened. Enter the master code to unlock the unit, as indicated by the lock icon light going OFF. It is now safe to undo the side latches and open the unit.

Hotkeys

Toggle Sound: By default, the sound is ON. To toggle the sound ON/OFF you need to wake up LifePod® by tapping the center Lock Pad (Fig T) then press and hold keys ‘2’ and ‘3’ together. The status LED (Fig R) will flash RED indicating OFF or GREEN indicating ON.

Using the Micro USB Port

A micro-USB port is built into LifePod behind the front protective rubber cover.

In the event the battery dies while traveling, and you do not have access to the backup keys, you can power on the unit using the backup micro-USB port.

Simply open the rubber cover and plug in a micro-USB cable (not included) into the port. While the cable is plugged into
an external power source, LifePod will function normally allowing you to enter the code and open the unit.

Backup Key Access

The keyhole is located beneath the front protective rubber cover.

Two backup keys are provided. In the event these are needed to open the LifePod, simply open the protective cover, insert one of the backup keys, and turn the key clockwise 90 degrees.

IMPORTANT: Always make sure the front protective cover is closed tightly to ensure the unit is sealed correctly for protection from the elements.

Using Keylock

Your LifePod is equipped with an anti-hacking feature for enhanced security. Using the key lock, you can disable the exterior lock from functioning.

OFF
Default setting. The exterior lock is engaged and fully functional.

ON
The exterior lock is disengaged. Meaning LifePod’s lock can not be picked open by any hacking and renders the lock useless.

IMPORTANT: When key lock is ON, the backup keys will not be able to open the unit. Use with caution. In the event of battery failure, the micro-USB port can still be used to provide power and open the unit.

Tethering Safe

Included is a tether lanyard that can be used to secure the LifePod to a fixed object.

1) First wrap the looped end of the tether around an object of your choice, such as a seat bracket under your vehicle’s seat.

2) Pull the adapter piece through the loop, and cinch tight.

3) Place the adapter piece in its slot in the LifePod, and close the lid.

TIP: A heavy duty steel security cable can be purchased separately if preferred.

Seasoning LifePod Humidor

STEP 1

Remove the cedar tray from your LifePod.

STEP 2

Place the cedar tray in an airtight container or zip-lock bag along with an 84% seasoning pack for 3 days.

Boveda makes 60 gram seasoning packs that can be found here: https://store.bovedainc.com/

STEP THREE

Return the battery the Bluetooth module. Then install the cedar tray back inside your LifePod and place a humidity control pack with your preferred %RH inside the control pack pocket on the lid.

Enjoy! https://store.bovedainc.com/collections/boveda-for-tobacco

We recommend reseasoning your Humidor once a year.

How long will my battery last?

A new 9v Alkaline battery will last up to one year with normal use. Normal use is locking and unlocking the LifePod 1-2 times per day.

How do I unlock the case if the battery is dead but the case is locked?

Plug a micro-USB cable into the front micro-USB port to power the unit so you can unlock and replace the battery.

Manual

Available Manuals

The following digital product manuals are available for use.

LifePod Humidor

Still need help?

We’ve got you covered.