VTi/VT

1) To recharge the safe, plug the micro-USB into the micro-USB receiving jack located on the right side of the safe and connect to a standard USB port or wall outlet using the AC power adapter. Approximate recharge time is 2.5 hours.

2) The LED next to the receiving jack on the side of the safe will glow RED indicating charging and GREEN indicating charged.

Charging Tips!

A) After installing the battery, use the charging kit provided to charge the unit 100%.

B) The charging kit can also function as an external power supply, which means you can open your safe even when the battery is depleted.

C) Leaving your safe plugged in continually will not harm the safe or battery. However, to preserve battery life we suggest that you unplug occasionally to allow the battery to cycle down.

D) A specially designed Vaultek powerpack is available as a separate accessory to extend operation time.

E) The adapter used to charge the battery should output 5V/2000mA or above when using micro-USB cable.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

The 1st and 2nd fingerprints will be recognized as administrative fingerprints and will be used to authorize additional users 3 to 20. To program additional users please “Programming Additional Prints”.

Fingerprint TIPS!

A) Be sure your finger is flat against the scanner (parallel to safe) and your cuticle is over the center of the scanner (this allows the scanner to read where most of the fingerprint details are located).

B) Rotate your finger slightly between registration scans to store print variations for increased accuracy.

C) Biometric technology is dependent on our anatomical information, and in some cases different fingers may program better than others. For example, your index finger may not register very well, but your thumb may contain higher detail levels and have a much higher success rate. We suggest to try different fingers including your thumb and see if you have better results.

D) To increase success rate register the same finger multiple times. Note, that adding more than two fingerprints requires authorization from the two administrative prints.

STEP 1 : Program the 1st Admin Print

1) Open the safe.

2) Program the 1st fingerprint by pressing holding the ‘2’ key then the “PROGRAM” button together for 3 seconds until the first LED on the status bar located above the fingerprint sensor blinks RED.

2) Place your finger on the fingerprint scanner for the 1st of five scans. When the safe beeps and the first status bar lights up GREEN remove your finger.

Troubleshooting! If the status bar LED turns RED then remove your finger and reposition the finger on the fingerprint scanner.

3) Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift. You will repeat this process until all status bars (1-5) are solid GREEN.

4) Close the door and test to see if the safe will open using your fingerprint.

STEP 2 : Program the 2nd Admin Print

1) Program the 2nd fingerprint by pressing holding the ‘2’ key then the “PROGRAM” button together for 3 seconds until the first LED on the status bar located above the fingerprint sensor blinks RED.

2) Place your finger on the fingerprint scanner for the 1st of five scans. When the safe beeps and the first status bar lights up GREEN remove your finger.

3) Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift. You will repeat this process until all status bars (1-5) are solid GREEN.

Once both admin prints are enrolled you can program additional prints. Your safe can store up to 20 unique fingerprints. To program addition prints refer to “Programming Additional Prints”.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

The first two fingerprints programmed into the safe are the administrative fingerprints. Any additional users programmed require authorization from one of these fingerprints.

1) Open the safe. Program the additional fingerprints by pressing and holding the ‘2’ key then the “PROGRAM” button together (3 seconds). The entire status bar will blink RED prompting you to scan one of the administrative fingerprints.

2) Place one of the two programmed administrative fingerprints on the scanner and remove when the safe beeps and the entire status bar blinks GREEN. When the first status bar starts blinking RED you can enroll a NEW fingerprint.

Tip! If the administrative print is left on the scanner too long the safe will begin to program that fingerprint into the safe again and not the NEW fingerprint. If this happens start over with step one.

3) Using the helpful fingerprint tips place the NEW finger on the scanner. When the safe beeps and the first LED in the status bar lights up GREEN remove your finger.

4) Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift. You will repeat this process until all status bar LEDs (1-5) are solid GREEN.

TIP! Repeat steps 1 through 4 to add additional fingerprints.

Troubleshooting! If you are having difficulty with your print, program the same fingerprint 4 or 5 times. You have 20 slots available for programming and you can also try your thumb as it has more surface area to read.

Individual fingerprints cannot be deleted from the keypad on the safe. Following this procedure will erase all the fingerprints including both administrative fingerprints. Individual fingerprints can be deleted from the Vaultek® Bluetooth app.

1) Press and hold the ‘3’ key and “PROGRAM” button together until all the status bar LEDs light up RED and let go.

2) Enter your master code on the keypad. If the code is correct, all the status bar LEDs will blink GREEN and the safe will beep indicating deletion of all the fingerprints.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

If you are having difficulty with your print, program the same fingerprint 4 or 5 times. You have 20 slots available for programming and you can also try your thumb as it has more surface area to read.

Let’s perform a soft reset of the scanner by deleting the fingerprints on the safe.

STEP 1 : Delete Fingerprints

First, delete the prints you have programmed in so far, and try again with the tips below:

1) Press and hold keys ‘3’ and ‘5’ at same time until all keys light up red (takes about 3 seconds). Let go of keys ‘3’ and ‘5’ and enter the master pin code.

2) You’ve cleared the prints and ready to start fresh!

Fingerprint TIPS!

Tip! During the 5 scan programming process for each finger, slightly repositioning your finger after each scan will store more information and increase your success rate.

Tip! To increase success rate register the same finger multiple times. Note, that adding more than two fingerprints requires authorization from the two administrative prints.

STEP 2 : Program the 1st Admin Print

Biometric technology is dependent on our anatomical information, and in some cases different fingers may program better than others. For example, your index finger may not register very well, but your thumb may contain higher detail levels and have a much higher success rate. We suggest to try different fingers including your thumb and see if you have better results.

1) Open the safe.

2) Program the 1st fingerprint by pressing holding the ‘2’ key then the “PROGRAM” button together for 3 seconds until the first LED on the status bar located above the fingerprint sensor blinks RED.

2) Place your finger on the fingerprint scanner for the 1st of five scans. When the safe beeps and the first status bar lights up GREEN remove your finger.

Troubleshooting! If the status bar LED turns RED then remove your finger and reposition the finger on the fingerprint scanner.

3) Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift. You will repeat this process until all status bars (1-5) are solid GREEN.

4) Close the door and test to see if the safe will open using your fingerprint.

STEP 3 : Program the 2nd Admin Print

1) Program the 2nd fingerprint by pressing holding the ‘2’ key then the “PROGRAM” button together for 3 seconds until the first LED on the status bar located above the fingerprint sensor blinks RED.

2) Place your finger on the fingerprint scanner for the 1st of five scans. When the safe beeps and the first status bar lights up GREEN remove your finger.

3) Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift. You will repeat this process until all status bars (1-5) are solid GREEN.

Once both admin prints are enrolled you can program additional prints. Your safe can store up to 20 unique fingerprints.

STEP 4 : Program Additional Prints

1) Open the safe. Program the additional fingerprints by pressing and holding the ‘2’ key then the “PROGRAM” button together (3 seconds). The entire status bar will blink RED prompting you to scan one of the administrative fingerprints.

2) Place one of the two programmed administrative fingerprints on the scanner and remove when the safe beeps and the entire status bar blinks GREEN. When the first status bar starts blinking RED you can enroll a NEW fingerprint.

Tip! If the administrative print is left on the scanner too long the safe will begin to program that fingerprint into the safe again and not the NEW fingerprint. If this happens start over with step one.

3) Using the helpful fingperint tips place the NEW finger on the scanner. When the safe beeps and the first LED in the status bar lights up GREEN remove your finger.

4) Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift. You will repeat this process until all status bar LEDs (1-5) are solid GREEN.

Tip! Repeat steps 1 through 4 to add additional fingerprints.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

1) Get the App. Download the Vaultek Bluetooth app from the Google Play store or Apple store.

Important! Do not download the Vaultek WiFi app as that is used for WiFi models only.

2) Make sure your phone’s Bluetooth settings are set to ON, and open the Vaultek app to begin.

3) Next, create a Pattern Lock. This is an added layer of protection to safeguard your safe and prevent unauthorized access in the event your phone is misplaced. To create your pattern lock, simply drag your finger along the screen to connect at least four dots. This unique pattern will be required each time you open the app.

4) Now select your safe. After a few seconds your safe will appear in the search. You can drag the screen downwards to refresh if you are not seeing your safe listed. Select your safe, and enter your safe’s master code when prompted. This is the same code used to open the safe using the numeric keypad.

Troubleshooting! As a security measure, if too many incorrect master code entries are entered, your safe’s Bluetooth will disable and must be toggled ON again using the hot key sequence.

5) Finally, sync your phone – A) Press and hold keys ‘4’ and ‘5’ on your safe followed by the “PROGRAM” button together for 3 seconds to start the syncing protocol. B) When the status bar starts blinking RED you can finalize the pairing sequence from your app screen by pressing ‘OK’. The safe’s status bar will flash GREEN and beep when complete. If the status bar flashes RED with two beeps you will need to start over with step 4.

Tip! This pairing sequence offers enhanced security protection and can only be used to pair one phone to your safe. If the process is repeated with a different phone, the previous phone will be overridden and disconnected from the safe.

Tip! If you change your safe’s master code after pairing, the safe will no longer connect to your app, and you will be prompted to enter the new code when needed.

Remote Unlock: This feature will be grayed out as a default and will need to be enabled. Refer to “Unlock feature is grayed out on the app”.

Note, Vaultek does not in any way access your personal data (including photos, locations, contacts, etc). The app requires permissions to store certain preferences such as safe settings and fingerprint ID names in the memory of your phone. It also uses the Bluetooth function of your phone for wireless communication with your safe.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

1) From the Vaultek app dashboard select “More” from the lower right corner.

2) Select “Name Your Safe”.

3) Now name your safe to whatever you like.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

By default, the unlock feature is disabled. To toggle ON press and hold keys “1” and “4” followed by the “PROGRAM” button for 3 seconds. If the status bar LED turns GREEN the unlock feature is enabled. If the status bar LED turns RED the unlock feature is disabled.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

You must follow all 3 steps for Nano Key to successfully pair to your safe.

1) Press and hold the ‘5’ key then “PROGRAM” button together (3 seconds) until all status bar LEDs blink RED.

2) Aim Nano Key towards the safe and press. If all the lights on the status bar glow GREEN and safe beeps, the Nano Key is paired successfully; if all lights on the status bar blink RED, the Nano Key failed to pair. In this case, simply start over with step 1.

3) Set Entry Mode: To toggle from the keypad press and hold the ‘6’ key then “PROGRAM” button together. The status bar will communicate as directed.

Off – Keys Turn Solid RED

Progressive Entry Mode – Keys Blink Green
Safe goes into sleep mode and will require you to wake up the safe before using Nano Key. You can wake up the safe by pressing any key or brushing your hand across the keypad of the safe (backlit keys will turn RED).

On Demand Entry Mode – Keys Solid Green
This mode grants immediate access to your safe without having to wake it up.

Warning! On Demand Entry Mode can open a safe in another room and/or out of sight. To reduce the risk of an unattended open safe we recommend using Progressive Entry Mode.

On Demand Entry mode requires significant power usage and can greatly reduce operation time. We suggest setting the Nano Key to Progressive Entry Mode to conserve battery.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

You can toggle entry modes from the keypad or Vaultek Bluetooth app.

1) To toggle from the keypad press and hold the ‘6’ key then “PROGRAM” button together. The status bar will communicate as directed.

Off – Keys Turn Solid RED

Progressive Entry Mode – Keys Blink Green
Safe goes into sleep mode and will require you to wake up the safe before using Smart Key. You can wake up the safe by pressing any key or brushing your hand across the keypad of the safe (backlit keys will turn RED).

On Demand Entry Mode – Keys Solid Green
This mode grants immediate access to your safe without having to wake it up.

Warning: On Demand Entry Mode can open a safe in another room and/or out of sight. To reduce the risk of an unattended open safe we recommend using Progressive Entry Mode.

On Demand Entry mode requires significant power usage and can greatly reduce operation time. We suggest setting the Smart Key to Progressive Entry Mode to conserve battery.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

Nano Key Biometric is capable of storing 20 prints. The first print is the Admin print. This print is necessary to authorize additional prints and authorize the deletion of all prints.

Before programming the fingerprints to Nano Key Biometric lets cover a few tips.

Fingerprint TIPS!

1) Place the core of the fingerprint flat over the center of the scanner. This allows the scanner to read where most of the fingerprint detail is located.

2) Rotate your finger slightly between registration scans to store print variations for increased accuracy.

3) Biometric technology is dependent on our anatomical information, and in some cases different fingers may program better than others. For example, your index finger may not register very well, but your thumb may contain higher detail levels and have a much higher success rate. We suggest to try different fingers including your thumb and see if you have better results.

4) To increase success rate register the same finger multiple times. Note, that adding more than two fingerprints requires authorization from the two administrative prints.

STEP 1 : Programming Fingerprints on Nano Key Biometric

The first print is the admin print. This print is necessary to authorize additional prints and authorize the deletion of all prints.

1) Quickly press the PROGRAM button. The LED ring will turn solid RED indication you can place your fingerprint on the scanner for the first of (3) registrations scans.

2) Place your thumb or finger on the scanner, when you hear a confirmation beep and the LED ring flashes GREEN, lift your finger and repeat two more registration scans to complete programming for the first user.

You can program additional users using the steps below.

You are now ready to pair Nano Key 2.0 Biometric to your safe.

Programming Additional Prints

1) Quickly press the PROGRAM button. The LED ring will turn solid YELLOW requesting you to place the Admin print on the scanner to authorize the request to add another user.

2) When successful, you will hear a confirmation beep and the LED ring will flash GREEN then back to RED indicating you to can proceed with the first of (3) registration scans for the new print.

Troubleshooting! If you hear two beeps and the LED ring stays RED, the scan was not accepted and you will need to start again.

Tip! A total of 19 fingerprints can be programmed outside the first Admin print.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

You can pair Nano Key Biometric to your safe once fingerprints are enrolled in Nano Key Biometric.

You must follow all 3 steps for Nano Key Biometric to successfully pair to your safe.

1) Press and hold the ‘5’ key then “PROGRAM” button together (3 seconds) until all status bar LEDs blink RED.

2) Aim Nano Key Biometric towards the safe and scan an authorized fingerprint. If all the lights on the status bar glow GREEN and safe beeps, the Nano Key Biometric is paired successfully; if all lights on the status bar blink RED, the Nano Key Biometric failed to pair. In this case, simply start over with step 1.

3) To finalize the pairing you need set an Entry Mode. To toggle from the keypad press and hold the ‘6’ key then “PROGRAM” button together. The status bar will communicate as directed.

Off – Keys Turn Solid RED

Progressive Entry Mode – Keys Blink Green
Safe goes into sleep mode and will require you to wake up the safe before using Nano Key Biometric. You can wake up the safe by pressing any key or brushing your hand across the keypad of the safe (backlit keys will turn RED).

On Demand Entry Mode – Keys Solid Green
This mode grants immediate access to your safe without having to wake it up.

Warning! On Demand Entry Mode can open a safe in another room and/or out of sight. To reduce the risk of an unattended open safe we recommend using Progressive Entry Mode.

On Demand Entry mode requires significant power usage and can greatly reduce operation time. We suggest setting the Nano Key Biometric to Progressive Entry Mode to conserve battery.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

This process will unpair Nano Key Biometric, and will delete all fingerprints. You can not delete individual fingerprints.

1) Press and hold the top PROGRAM button on Nano Key Biometric until the LED ring turns YELLOW. This prompts you to scan the Admin print first. The Admin print is the first fingerprint enrolled in Nano Key Biometric, and must be scanned to authorize the unpair.

2) A single confirmation beep and GREEN LED ring confirms unpair is complete.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

This process will unpair Nano Key Biometric, and will delete all fingerprints. You can not delete individual fingerprints.

1) Press and hold the top PROGRAM button on Nano Key Biometric until the LED ring turns YELLOW. This prompts you to scan the Admin print first. The Admin print is the first fingerprint enrolled in Nano Key Biometric, and must be scanned to authorize the deletion of all prints.

2) A single confirmation beep and GREEN LED ring confirms delete is complete.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

Simply plug in the micro-USB charging cable provided for 2.5 hours to recharge the battery.

When the battery is full, the LED ring will glow solid WHITE. To turn off the LED ring you can touch the scanner or unplug the charging cable.

Approximate battery life under normal usage is 3 months.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

A) Your safe is powered by a 3.7V 18650 rechargeable lithium-ion flat top battery. A minimum 2000 mAh capacity is required, however 2200 mAh or higher can reused to increase operation time.

B) The adapter used to charge the battery should output 5V/2000mA or above when using micro-USB cable.

TIP! Leaving your safe plugged in continually will not harm the safe or battery. However, to preserve battery life we suggest that you unplug occasionally to allow the battery to cycle down.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

Your safe can be secured a few different ways. Included is a security cable to attach your safe to larger stationary objects. There are also mounting screws included to secure the safe to a flat surface using the pre-drilled holes on the bottom.

Using the Security Cable

1) Loop the included steel security cable around a secured object.

2) Run the end of the cable through the eye of the other end and pull around the object.

3) Place the end of the security cable inside the fully enclosed quick release cable mount inside your Vaultek safe.

4) Make sure the safe closes with the cable secured inside the quick release cable mount.

Using the Mounting Screws

Tip! Make sure you have enough clearance for the lid to open properly before mounting the safe.

1) Position the safe on a flat surface where you want to mount it.

2) Use a pencil to mark the holes for drilling.

3) Drill pilot holes.

4) Position safe in place and install screws through safe into pilot holes. Tighten screws.

Optional Mounting Plate Accessory

The Vaultek mounting plate allows you to securely rack your VT Series safe in place, with the added flexibility of being able to remove the safe when needed. Designed for use with the VTi and VT.

To check for tampering press and hold keys ‘2’ and ‘4’ together for 3 seconds. The status bar will glow RED to indicate tampering or GREEN to indicate no tampering. You can reset the tamper detection by opening the safe through one of the authorized entry points.

If the Alert of Unlock is on, and someone opens the safe with either the key or by picking the lock, the keypad will start flashing. To toggle Alert Unlock press and hold  keys ‘3’ and ‘6’ then “PROGRAM” button together for 3 seconds. The keypad will flash GREEN indicating enabled or RED indicating disabled. If ON and activated it can only be cleared by entering master code. Default is OFF..

To toggle the sound ON/OFF press and hold keys ‘1’ and ‘3’ together for 3 seconds. If the status bar glows GREEN and beeps, the sound is ON; if the status bar glows RED, the sound is OFF.

Save battery life by disabling the proximity sensor, keypad, and status bar. To toggle travel mode ON/OFF press and hold keys ‘1’, and ‘8’ together until safe beeps and the status bar lights up. If the status bar glows RED and beeps, the safe is disabled; if the status bar glows GREEN and beeps, the safe is operational.

You can view the safe battery status using the hot key shortcut on the keypad or in the Vaultek Bluetooth app.

To check the battery level press and hold keys ‘1’ and ‘8’ together on the keypad (3 seconds). The status will glow GREEN or RED to indicate the battery level.

If 5 LEDs glow green: 80%-100%

If 4 LEDs glow green: 60%-80%

If 3 LEDs glow green: 40%-60%

If 2 LEDs glow green: 20%-40%

If 1 LED glows red: 10%-20%

If 1 LED blinks red: less than 10%

To toggle the interior light ON/OFF press and hold keys ‘5’ and ‘7’ together for 3 seconds. With the light toggled to ON you can press the “LIGHT” button inside the safe to illuminate the light and can also adjust the interior light in the app for Bluetooth safes. If the light is toggled OFF the light will be disabled.

To toggle the Bluetooth ON/OFF press and hold the ‘4’ key then “PROGRAM” button together for 3 seconds. If the status bar glows GREEN Bluetooth is ON. If the status bar glows RED Bluetooth is OFF. If Bluetooth is toggled OFF all app functions will be disabled and your safe is undiscoverable.

By default, the unlock feature on the Vaultek® Bluetooth app will be disabled. To toggle this feature press and hold keys ‘1’ and ‘4’ and “PROGRAM” button together for 3 seconds. If the status bar LED turns GREEN the unlock feature is enabled. If the status bar LED turns RED the unlock feature is disabled.

You can toggle the Nano Key entry mode using the hot key shortcut on the keypad or inside Vaultek Bluetooth app.

To toggle Nano Key entry modes press and hold the ‘6’ key then “PROGRAM” button together for 3 seconds. The status bar will indicate each mode as listed below.

Off – Keys Turn Solid RED

Progressive Entry Mode – Keys Blink Green
Safe goes into sleep mode and will require you to wake up the safe before using Nano Key. You can wake up the safe by pressing any key or brushing your hand across the keypad of the safe (backlit keys will turn RED).

On Demand Entry Mode – Keys Solid Green
This mode grants immediate access to your safe without having to wake it up.

Warning: On Demand Entry Mode can open a safe in another room and/or out of sight. To reduce the risk of an unattended open safe we recommend using Progressive Entry Mode.

On Demand Entry mode requires significant power usage and can greatly reduce operation time. We suggest setting the Nano Key to Progressive Entry Mode to conserve battery.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

Your Vaultek® safe has a built-in accelerometer and corresponding alarm that alerts of any attacking to your safe including bumps and impacts, DMT (Impact Detection).

DMT is enabled by default and its sensitivity has three settings; Low, Medium, and High.

You can toggle through these settings by pressing and holding the ‘7’ key then “PROGRAM” button together for 3 seconds. If all FIVE lights on the status bar glow solid GREEN, the High setting is enabled; If FOUR lights on the status bar glow solid GREEN, the Medium setting is enabled; if THREE lights on the status bar glow GREEN, the Low setting is enabled; if all lights on the status bar glow RED, DMT is disabled (OFF).

To toggle the Dual Entry ON/OFF press and hold the ‘8’ key then “PROGRAM” button together for 3 seconds. If the status bar glows GREEN, this feature is ON. If the status bar glows RED this feature is OFF. If the Dual Entry is toggled ON, you will be required to enter your master code and fingerprint (and vice versa) to open the safe. This mode requires that at least one fingerprint be programmed in the safe.

To order a set of keys, charging kit, or steel cable, fill out our Spare Parts form.

If you are having difficulty with your print, program the same fingerprint 4 or 5 times. You have 20 slots available for programming and you can also try your thumb as it has more surface area to read.

Let’s perform a soft reset of the scanner by deleting the fingerprints on the safe.

STEP 1 : Delete Fingerprints

First, delete the prints you have programmed in so far, and try again with the tips below:

1) Press and hold keys ‘3’ and ‘5’ at same time until all keys light up red (takes about 3 seconds). Let go of keys ‘3’ and ‘5’ and enter the master pin code. You’ve cleared the prints and ready to start fresh!

Tip! Biometric technology is dependent on our anatomical information, and in some cases different fingers may program better than others. For example, your index finger may not register very well, but your thumb may contain higher detail levels and have a much higher success rate. We suggest to try different fingers including your thumb and see if you have better results.

Tip! During the 5 scan programming process for each finger, slightly repositioning your finger after each scan will store more information and increase your success rate.

Tip! To increase success rate register the same finger multiple times. Note, that adding more than two fingerprints requires authorization from the two administrative prints.

STEP 2 : Program the 1st Admin Print

1) Open the safe.

2) Program the 1st fingerprint by pressing holding the ‘2’ key then the “PROGRAM” button together for 3 seconds until the first LED on the status bar located above the fingerprint sensor blinks RED.

2) Place your finger on the fingerprint scanner for the 1st of five scans. When the safe beeps and the first status bar lights up GREEN remove your finger.

Troubleshooting! If the status bar LED turns RED then remove your finger and reposition the finger on the fingerprint scanner.

3) Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift. You will repeat this process until all status bars (1-5) are solid GREEN.

4) Close the door and test to see if the safe will open using your fingerprint.

STEP 3 : Program the 2nd Admin Print

1) Program the 2nd fingerprint by pressing holding the ‘2’ key then the “PROGRAM” button together for 3 seconds until the first LED on the status bar located above the fingerprint sensor blinks RED.

2) Place your finger on the fingerprint scanner for the 1st of five scans. When the safe beeps and the first status bar lights up GREEN remove your finger.

3) Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift. You will repeat this process until all status bars (1-5) are solid GREEN.

Once both admin prints are enrolled you can program additional prints. Your safe can store up to 20 unique fingerprints.

STEP 4 : Program Additional Prints

1) Open the safe. Program the additional fingerprints by pressing and holding the ‘2’ key then the “PROGRAM” button together (3 seconds). The entire status bar will blink RED prompting you to scan one of the administrative fingerprints.

2) Place one of the two programmed administrative fingerprints on the scanner and remove when the safe beeps and the entire status bar blinks GREEN. When the first status bar starts blinking RED you can enroll a NEW fingerprint.

Tip! If the administrative print is left on the scanner too long the safe will begin to program that fingerprint into the safe again and not the NEW fingerprint. If this happens start over with step one.

3) Using the helpful fingperint tips place the NEW finger on the scanner. When the safe beeps and the first LED in the status bar lights up GREEN remove your finger.

4) Place finger again over the scanner until the safe beeps and the second status LED lights up GREEN and lift. You will repeat this process until all status bar LEDs (1-5) are solid GREEN.

Tip! Repeat steps 1 through 4 to add additional fingerprints.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

Make sure you are using the Vaultek Bluetooth app and not the Vaultek Bluetooth 2.0 app or Vaultek WiFi app.

The device name you may be seeing in the “Select Your Safe” is the default name assigned to the safe. Example: “VAULTEK-1B7A”. Select that and once you successfully pair you can change the name.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

A) In the event an authorized user paired another phone to your safe you will be prompted to re-pair. The safe is designed to pair with one phone at a time.

B) In the event an authorized user changed the safe’s master code after pairing, the safe will no longer connect to your app, and you will be prompted to enter the new code when needed.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

1) By default, the unlock feature is disabled. To toggle ON press and hold keys “1” and “4” followed by the “PROGRAM” button for 3 seconds. If keys ‘2’ and ‘3’ turn GREEN the unlock feature is enabled. If keys ‘2’ and ‘3’ turn RED the unlock feature is disabled.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

Having trouble viewing your safe when setting up your app please try the steps below.

1) Delete the App

2) Soft Reset: Remove battery for 5 seconds and reinstall. Note, the program info will not be affected.

3) Re-install App: Download and re-install the Vaultek app.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!

Once you pair the Nano Key with your safe it will be immediately active to test functionality and then turn off.

Nano Key will need to be set to either Progressive Entry Mode or On Demand Entry Mode immediately after pairing.

Having issues? Please email our support team at support@vaulteksafe.com. They would be more than happy to help you out!